Qdatasheet_Logo     Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
HOME  >>>  Integrated Silicon Solution  >>> IS25LQ016 PDF

IS25LQ016 Datasheet PDF - Integrated Silicon Solution

Part NameDescriptionManufacturer
IS25LQ016 8Mbit Single Operating Voltage Serial Flash Memory ISSI
Integrated Silicon Solution ISSI
Other PDF  no available.
IS25LQ016 Datasheet PDF : PDF DOWNLOAD   
IS25LQ016 image

GENERAL DESCRIPTION
The IS25LQ016 are 16 Mbit Serial Peripheral Interface (SPI) Flash memories, providing single-, dual or quad output. The devices are designed to support a 50 MHz fclock rate in normal read mode, and 104 MHz in fast read (Quad output is 100MHz), the fastest in the industry. The devices use a single low voltage power supply, ranging from 2.3 Volt to 3.6 Volt, to perform read, erase and program operations. The devices can be programmed in standard EPROM programmers.

FEATURES
• Single Power Supply Operation
    - Low voltage range: 2.3 V - 3.6 V
• Memory Organization
    - IS25LQ016: 2048K x 8 (16 Mbit)
• Cost Effective Sector/Block Architecture
    - 16Mb : Uniform 4KByte sectors / Thirty-two uniform 64KByte blocks
• Serial Peripheral Interface (SPI) Compatible
    - Supports single-, dual- or quad-output
    - Supports SPI Modes 0 and 3
    - Maximum 50 MHz clock rate for normal read
    - Maximum 104 MHz clock rate for fast read
    - Maximum 208MHz clock rate equivalent Dual SPI
    - Maximum 400MHz clock rate equivalent Quad SPI
• Byte Program Operation
    - Typical 10 us/Byte
• Page Program (up to 256 Bytes) Operation
    - Maximum 0.7ms per page program
• Sector, Block or Chip Erase Operation
    - Sector Erase (4KB) -> 150ms (Typ)
    - Block Erase (64KB) -> 500ms (Typ)
    - Chip Erase -> 5s (Typ)
• Low Power Consumption
    - Max 12 mA active read current
    - Max 20 mA program/erase current
    - Max 30 uA standby current
• Hardware Write Protection
    - Protect and unprotect the device from write operation by Write Protect (WP#) Pin
• Software Write Protection
    - The Block Protect (BP3, BP2, BP1, BP0) bits allow partial or entire memory to be configured as read-only
• High Product Endurance
    - Guaranteed 100,000 program/erase cycles per single sector
    - Minimum 20 years data retention
• Industrial Standard Pin-out and Package
    - 8-pin 208mil SOIC
    - 8-contact WSON
    - PDIP
    - 8-pin 208mil VSOP
    - Lead-free (Pb-free) package
• Additional 256-byte Security information one-time programmable (OTP) area
• Special protect function
    - Safe guard function (Appendix 1)
    - Sector unlock function (Appendix 2)

 

Other manufacturer searches related to IS25LQ016

Part NameDescriptionPDFManufacturer
PM25LD010 512Kbit/1 Mbit / 2 Mbit Single Operating Voltage Serial Flash Memory With 100 MHz Dual-Output SPI Bus VIEW Unspecified
M25P05-VMN6T 512 Kbit, Low Voltage, Serial Flash Memory With 20 MHz SPI Bus Interface VIEW STMicroelectronics
29W040 4 Mbit 512Kb x8 / Uniform Block Low Voltage Single Supply Flash Memory VIEW STMicroelectronics
MX29F8100 8M-BIT [1M x 8/512K x 16] CMOS SINGLE VOLTAGE FLASH MEMORY VIEW Macronix International
ST7-STICK45 8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI VIEW STMicroelectronics
F25L016A 16Mbit (2Mx8) 3V Only Serial Flash Memory VIEW [Elite Semiconductor Memory Technology Inc.
ST7FDALI 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI VIEW STMicroelectronics
LH28F004SU 4Mbit(512Kbit x 8, 256 Kbit x 16) 5V Single Voltage Flash Memory VIEW Sharp Electronics
M25P10 1 Mbit Low Voltage Paged Flash Memory With 20 MHz Serial SPI Bus Interface VIEW STMicroelectronics
M29W400B NND - 4 MBIT (512KB X8 OR 256KB X16, BOOT BLOCK) LOW VOLTAGE SINGLE SUPPLY FLASH MEMORY VIEW STMicroelectronics

Share Link : 

All Rights Reserved © qdatasheet.com 2015 - 2020  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]