Qdatasheet_Logo    Integrated circuits, Transistor, Semiconductors Search and Free Datasheet PDF Download Site
Part Number :


C617C103PFR5T View Datasheet(PDF) - KEMET

Part NameC617C103PFR5T Kemet
KEMET Kemet
DescriptionMULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED
'C617C103PFR5T' PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next
MULTILAYER CERAMIC CAPACITORS/AXIAL
& RADIAL LEADED
Multilayer ceramic capacitors are available in a
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
edges of the laminated structure. The entire structure is
fired at high temperature to produce a monolithic
block which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
a wide range of characteristics. The EIA standard for
ceramic dielectric capacitors (RS-198) divides ceramic
dielectrics into the following classes:
Class III: General purpose capacitors, suitable
for by-pass coupling or other applications in which
dielectric losses, high insulation resistance and
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
Class I: Temperature compensating capacitors, II capacitors except for temperature characteristics,
suitable for resonant circuit application or other appli- which are greater than ± 15%. Class III capacitors
cations where high Q and stability of capacitance char- have the highest volumetric efficiency and poorest
acteristics are required. Class I capacitors have stability of any type.
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
from materials which are not ferro-electric, yielding
superior stability but low volumetric efficiency. Class I
capacitors are the most stable type available, but have
the lowest volumetric efficiency.
KEMET leaded ceramic capacitors are offered in
the three most popular temperature characteristics:
C0G: Class I, with a temperature coefficient of 0 ±
30 ppm per degree C over an operating
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
Class II: Stable capacitors, suitable for bypass
X7R: Class II, with a maximum capacitance
or coupling applications or frequency discriminating
change of ± 15% over an operating temperature
circuits where Q and stability of capacitance char-
range of - 55°C to + 125°C.
acteristics are not of major importance. Class II
Z5U: Class III, with a maximum capacitance
capacitors have temperature characteristics of ± 15%
change of + 22% - 56% over an operating tem-
or less. They are made from materials which are
perature range of + 10°C to + 85°C.
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by Specified electrical limits for these three temperature
temperature, voltage, frequency and time.
characteristics are shown in Table 1.
SPECIFIED ELECTRICAL LIMITS
Parameter
Dissipation Factor: Measured at following conditions.
C0G – 1 kHz and 1 vrms if capacitance >1000pF
1 MHz and 1 vrms if capacitance 1000 pF
X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms
Z5U – 1 kHz and 0.5 vrms
Dielectric Stength: 2.5 times rated DC voltage.
Insulation Resistance (IR): At rated DC voltage,
whichever of the two is smaller
Temperature Characteristics: Range, °C
Capacitance Change without
DC voltage
* MHz and 1 vrms if capacitance 100 pF on military product.
Temperature Characteristics
C0G
X7R
Z5U
0.10%
2.5%
(3.5% @ 25V)
4.0%
Pass Subsequent IR Test
1,000 M F
or 100 G
1,000 M F
or 100 G
1,000 M F
or 10 G
-55 to +125
0 ± 30 ppm/°C
-55 to +125
± 15%
+ 10 to +85
+22%,-56%
Table I
4
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Direct download click here
Share Link : Kemet

New and Popular Datasheets

FDPF5N50NZU  FDPF44N25  FDPF44N25T  FDPF3N50NZ  FDP5N50NZ  FDP52N20  FDP18N20F  FDP12N50NZ  FDB20N50F  FCPF11N60T  FCP380N60E  FCP260N60E  2N7000  BAV199LT1  BAV199LT1G  2N5190  BCW72  CAT25010  MC74LVX4066  BDX33B  50C02CH  1N5333B  FCD5N60  FCPF190N60E_F152  FCPF190N60E  FCA20N60F109  FCA20N60  DTC114TE  MDD14N25C  MBR835  74AC32  SEMB10  SEMB11  MC1496  ATMEGA128  OP506A  OPB815L  OPB815WZ  SW-209  PH2729-25M  IXFE44N60  M74HC123  TSM103  LB-303VA  EF6840  M74HC164  TDA7439DS  1EDI30J12CP  2N2857  LM336BX25 

@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]