GENERAL DESCRIPTION
INTRODUCTION
The ST6200L/01L and 03L are low voltage mask programmed ROM version of ST62T00C,T01C and T03C OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version, with the exception of the LVD Reset and the OSG that are not available.

■ 2.4 to 3.9V Supply Operating Range
■ 4 MHz Maximum Clock Frequency
■ 0 to +70°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
   User selectable size
■ Data RAM: 64bytes
■ 9 I/O pins, fully programmable as:
   – Input with pull-up resistor
   – Input without pull-up resistor
   – Input with interrupt generation
   – Open-drain or push-pull output
   – Analog Input (except ST6203L)
■ 3 I/O lines can sink up to 12mA to drive LEDs
■ 8-bit Timer/Counter with 7-bit programmable prescaler
■ Digital Watchdog
■ 8-bit A/D Converter with up to 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
   Crystal Ceramic resonator or RC network
■ Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development
   System (connects to an MS-DOS PC via an RS232 serial line)

PRODUCT DESCRIPTION
SST’s ATA-Disk Module (ADM) is a low cost, high performance, embedded flash memory data storage system. This product is well suited for solid state mass storage applications offering new and expanded functionality while enabling cost effective designs.
The ADM is a solid state disk drive that is designed to replace conventional IDE hard disk drive and can be plugged into a standard IDE connector commonly found in desktop or portable PC systems.
ADM has built-in microcontroller and file management firmware that communicates with ATA standard interfaces; therefore, the ADM does not require additional or proprietary host software such as Flash File System (FFS) and Memory Technology Driver (MTD) software.
The ADM is designed to work at either 5V or 3.3V and is available in 8 to 192 MByte capacities. It uses standard ATA driver that is part of all major OS such as Windows 95/98/2000/NT/CE, MAC, UNIX, etc.
All signals, except WP#, are in compliance with the ATA specifications. WP# is used to write protect the information stored on the ADM. The WP# could be connected to the motherboard write protect control logic through a jumper. When WP# is low, the ADM is write protected to prohibit any inadvertent writes.
Every ADM comes with factory-programmed, 20-Byte long, unique identification number for extended data protection. This feature prevents unauthorized duplication by allowing encryption of customer data.
The ADM integrates a standard 40- or 44-pin female connector for easy and cost effective mounting on top of a standard IDE male connector commonly found on the system motherboards. ADM also offers user selectable Master/Slave operation through an external jumper setting.

FEATURES:
• ATA/IDE standard interface
   – 512 Bytes per sector
   – ATA command set compatible
   – Selectable Master/Slave Operation
   – Support Data Transfer Speed up to PIO Mode-4
• 8, 16, 24, 32, 48, 64, 96, 128, and 192 MByte capacities
• Standard Female IDE Connector
   – 40-pin and 44-pin
• Single Voltage Read and Write Operation
   – 5.0V-only for SST58SMxxx
   – 3.3V-only for SST58LMxxx
• Supports 5.0-Volt or 3.3-Volt Read and Write
   – 4.5-5.5V or 3.135-3.465V for Commercial
• Low Power Consumption
   – Active mode: 35 mA/55 mA (3.3V/5.0V) (typical)
   – Sleep mode: 100 µA/150 µA (3.3V/5.0V) (typical)
• Sustained Write Performance
   – Up to 1.4 MB/sec (host to flash)
• Extended Data Protection and Security
   – WP# pin for Data Protection
   – Factory-Programmed, 20-Byte Unique ID number
• Controller Overhead Command to DRQ
   – Less than 0.5 ms
• Zero Power Data Retention
   – Batteries not required for data storage
• Start Up Time
   – Sleep to read: 200 ns (typical)
   – Sleep to write: 200 ns (typical)
   – Power-on to Ready:200 ms (typical)
• Support for Commercial Temperature Range
   – 0°C to +70°C for Operating Commercial
   – -50°C to +100°C for non-Operating (storage)
• Extremely Rugged and Reliable
   – Built-in ECC support corrects 3 Bytes of error per 512 Byte sector
• Intelligent ATA/IDE Controller
   – Built-in microcontroller with intelligent firmware
   – Built-in Embedded Flash File System
• Power Management Unit
   – Immediate disabling of unused circuitry

GENERAL DESCRIPTION
INTRODUCTION
The ST6200L/01L and 03L are low voltage mask programmed ROM version of ST62T00C,T01C and T03C OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version, with the exception of the LVD Reset and the OSG that are not available.

■ 2.4 to 3.9V Supply Operating Range
■ 4 MHz Maximum Clock Frequency
■ 0 to +70°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
   User selectable size
■ Data RAM: 64bytes
■ 9 I/O pins, fully programmable as:
   – Input with pull-up resistor
   – Input without pull-up resistor
   – Input with interrupt generation
   – Open-drain or push-pull output
   – Analog Input (except ST6203L)
■ 3 I/O lines can sink up to 12mA to drive LEDs
■ 8-bit Timer/Counter with 7-bit programmable prescaler
■ Digital Watchdog
■ 8-bit A/D Converter with up to 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
   Crystal Ceramic resonator or RC network
■ Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development
   System (connects to an MS-DOS PC via an RS232 serial line)

PRODUCT DESCRIPTION
SST’s ATA-Disk Module (ADM) is a low cost, high performance, embedded flash memory data storage system. This product is well suited for solid state mass storage applications offering new and expanded functionality while enabling cost effective designs.
The ADM is a solid state disk drive that is designed to replace conventional IDE hard disk drive and can be plugged into a standard IDE connector commonly found in desktop or portable PC systems.
ADM has built-in microcontroller and file management firmware that communicates with ATA standard interfaces; therefore, the ADM does not require additional or proprietary host software such as Flash File System (FFS) and Memory Technology Driver (MTD) software.
The ADM is designed to work at either 5V or 3.3V and is available in 8 to 192 MByte capacities. It uses standard ATA driver that is part of all major OS such as Windows 95/98/2000/NT/CE, MAC, UNIX, etc.
All signals, except WP#, are in compliance with the ATA specifications. WP# is used to write protect the information stored on the ADM. The WP# could be connected to the motherboard write protect control logic through a jumper. When WP# is low, the ADM is write protected to prohibit any inadvertent writes.
Every ADM comes with factory-programmed, 20-Byte long, unique identification number for extended data protection. This feature prevents unauthorized duplication by allowing encryption of customer data.
The ADM integrates a standard 40- or 44-pin female connector for easy and cost effective mounting on top of a standard IDE male connector commonly found on the system motherboards. ADM also offers user selectable Master/Slave operation through an external jumper setting.

FEATURES:
• ATA/IDE standard interface
   – 512 Bytes per sector
   – ATA command set compatible
   – Selectable Master/Slave Operation
   – Support Data Transfer Speed up to PIO Mode-4
• 8, 16, 24, 32, 48, 64, 96, 128, and 192 MByte capacities
• Standard Female IDE Connector
   – 40-pin and 44-pin
• Single Voltage Read and Write Operation
   – 5.0V-only for SST58SMxxx
   – 3.3V-only for SST58LMxxx
• Supports 5.0-Volt or 3.3-Volt Read and Write
   – 4.5-5.5V or 3.135-3.465V for Commercial
• Low Power Consumption
   – Active mode: 35 mA/55 mA (3.3V/5.0V) (typical)
   – Sleep mode: 100 µA/150 µA (3.3V/5.0V) (typical)
• Sustained Write Performance
   – Up to 1.4 MB/sec (host to flash)
• Extended Data Protection and Security
   – WP# pin for Data Protection
   – Factory-Programmed, 20-Byte Unique ID number
• Controller Overhead Command to DRQ
   – Less than 0.5 ms
• Zero Power Data Retention
   – Batteries not required for data storage
• Start Up Time
   – Sleep to read: 200 ns (typical)
   – Sleep to write: 200 ns (typical)
   – Power-on to Ready:200 ms (typical)
• Support for Commercial Temperature Range
   – 0°C to +70°C for Operating Commercial
   – -50°C to +100°C for non-Operating (storage)
• Extremely Rugged and Reliable
   – Built-in ECC support corrects 3 Bytes of error per 512 Byte sector
• Intelligent ATA/IDE Controller
   – Built-in microcontroller with intelligent firmware
   – Built-in Embedded Flash File System
• Power Management Unit
   – Immediate disabling of unused circuitry

GENERAL DESCRIPTION
INTRODUCTION
The ST6200L/01L and 03L are low voltage mask programmed ROM version of ST62T00C,T01C and T03C OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version, with the exception of the LVD Reset and the OSG that are not available.

■ 2.4 to 3.9V Supply Operating Range
■ 4 MHz Maximum Clock Frequency
■ 0 to +70°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
   User selectable size
■ Data RAM: 64bytes
■ 9 I/O pins, fully programmable as:
   – Input with pull-up resistor
   – Input without pull-up resistor
   – Input with interrupt generation
   – Open-drain or push-pull output
   – Analog Input (except ST6203L)
■ 3 I/O lines can sink up to 12mA to drive LEDs
■ 8-bit Timer/Counter with 7-bit programmable prescaler
■ Digital Watchdog
■ 8-bit A/D Converter with up to 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
   Crystal Ceramic resonator or RC network
■ Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development
   System (connects to an MS-DOS PC via an RS232 serial line)

General Description
The LM1558 and the LM1458 are general purpose dual operational amplifiers. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent.
The LM1458 is identical to the LM1558 except that the LM1458 has its specifications guaranteed over the temperature range from 0˚C to +70˚C instead of −55˚C to +125˚C.

Features
■ No frequency compensation required
■ Short-circuit protection
■ Wide common-mode and differential voltage ranges
■ Low-power consumption
■ 8-lead can and 8-lead mini DIP
■ No latch up when input common mode range is exceeded

Features
Encased in ceramic package
High reliability against soldering heat and mechanical stress
Moisture-proof sealing
Low Profile Type (1.8 mm maximum in thickness)
Designed for reflow soldering
Flat-bottom plate for better mountings

PRODUCT DESCRIPTION
SST’s ATA-Disk Module (ADM) is a low cost, high performance, embedded flash memory data storage system. This product is well suited for solid state mass storage applications offering new and expanded functionality while enabling cost effective designs.
The ADM is a solid state disk drive that is designed to replace conventional IDE hard disk drive and can be plugged into a standard IDE connector commonly found in desktop or portable PC systems.
ADM has built-in microcontroller and file management firmware that communicates with ATA standard interfaces; therefore, the ADM does not require additional or proprietary host software such as Flash File System (FFS) and Memory Technology Driver (MTD) software.
The ADM is designed to work at either 5V or 3.3V and is available in 8 to 192 MByte capacities. It uses standard ATA driver that is part of all major OS such as Windows 95/98/2000/NT/CE, MAC, UNIX, etc.
All signals, except WP#, are in compliance with the ATA specifications. WP# is used to write protect the information stored on the ADM. The WP# could be connected to the motherboard write protect control logic through a jumper. When WP# is low, the ADM is write protected to prohibit any inadvertent writes.
Every ADM comes with factory-programmed, 20-Byte long, unique identification number for extended data protection. This feature prevents unauthorized duplication by allowing encryption of customer data.
The ADM integrates a standard 40- or 44-pin female connector for easy and cost effective mounting on top of a standard IDE male connector commonly found on the system motherboards. ADM also offers user selectable Master/Slave operation through an external jumper setting.

FEATURES:
• ATA/IDE standard interface
   – 512 Bytes per sector
   – ATA command set compatible
   – Selectable Master/Slave Operation
   – Support Data Transfer Speed up to PIO Mode-4
• 8, 16, 24, 32, 48, 64, 96, 128, and 192 MByte capacities
• Standard Female IDE Connector
   – 40-pin and 44-pin
• Single Voltage Read and Write Operation
   – 5.0V-only for SST58SMxxx
   – 3.3V-only for SST58LMxxx
• Supports 5.0-Volt or 3.3-Volt Read and Write
   – 4.5-5.5V or 3.135-3.465V for Commercial
• Low Power Consumption
   – Active mode: 35 mA/55 mA (3.3V/5.0V) (typical)
   – Sleep mode: 100 µA/150 µA (3.3V/5.0V) (typical)
• Sustained Write Performance
   – Up to 1.4 MB/sec (host to flash)
• Extended Data Protection and Security
   – WP# pin for Data Protection
   – Factory-Programmed, 20-Byte Unique ID number
• Controller Overhead Command to DRQ
   – Less than 0.5 ms
• Zero Power Data Retention
   – Batteries not required for data storage
• Start Up Time
   – Sleep to read: 200 ns (typical)
   – Sleep to write: 200 ns (typical)
   – Power-on to Ready:200 ms (typical)
• Support for Commercial Temperature Range
   – 0°C to +70°C for Operating Commercial
   – -50°C to +100°C for non-Operating (storage)
• Extremely Rugged and Reliable
   – Built-in ECC support corrects 3 Bytes of error per 512 Byte sector
• Intelligent ATA/IDE Controller
   – Built-in microcontroller with intelligent firmware
   – Built-in Embedded Flash File System
• Power Management Unit
   – Immediate disabling of unused circuitry

PRODUCT DESCRIPTION
SST’s ATA-Disk Module (ADM) is a low cost, high performance, embedded flash memory data storage system. This product is well suited for solid state mass storage applications offering new and expanded functionality while enabling cost effective designs.
The ADM is a solid state disk drive that is designed to replace conventional IDE hard disk drive and can be plugged into a standard IDE connector commonly found in desktop or portable PC systems.
ADM has built-in microcontroller and file management firmware that communicates with ATA standard interfaces; therefore, the ADM does not require additional or proprietary host software such as Flash File System (FFS) and Memory Technology Driver (MTD) software.
The ADM is designed to work at either 5V or 3.3V and is available in 8 to 192 MByte capacities. It uses standard ATA driver that is part of all major OS such as Windows 95/98/2000/NT/CE, MAC, UNIX, etc.
All signals, except WP#, are in compliance with the ATA specifications. WP# is used to write protect the information stored on the ADM. The WP# could be connected to the motherboard write protect control logic through a jumper. When WP# is low, the ADM is write protected to prohibit any inadvertent writes.
Every ADM comes with factory-programmed, 20-Byte long, unique identification number for extended data protection. This feature prevents unauthorized duplication by allowing encryption of customer data.
The ADM integrates a standard 40- or 44-pin female connector for easy and cost effective mounting on top of a standard IDE male connector commonly found on the system motherboards. ADM also offers user selectable Master/Slave operation through an external jumper setting.

FEATURES:
• ATA/IDE standard interface
   – 512 Bytes per sector
   – ATA command set compatible
   – Selectable Master/Slave Operation
   – Support Data Transfer Speed up to PIO Mode-4
• 8, 16, 24, 32, 48, 64, 96, 128, and 192 MByte capacities
• Standard Female IDE Connector
   – 40-pin and 44-pin
• Single Voltage Read and Write Operation
   – 5.0V-only for SST58SMxxx
   – 3.3V-only for SST58LMxxx
• Supports 5.0-Volt or 3.3-Volt Read and Write
   – 4.5-5.5V or 3.135-3.465V for Commercial
• Low Power Consumption
   – Active mode: 35 mA/55 mA (3.3V/5.0V) (typical)
   – Sleep mode: 100 µA/150 µA (3.3V/5.0V) (typical)
• Sustained Write Performance
   – Up to 1.4 MB/sec (host to flash)
• Extended Data Protection and Security
   – WP# pin for Data Protection
   – Factory-Programmed, 20-Byte Unique ID number
• Controller Overhead Command to DRQ
   – Less than 0.5 ms
• Zero Power Data Retention
   – Batteries not required for data storage
• Start Up Time
   – Sleep to read: 200 ns (typical)
   – Sleep to write: 200 ns (typical)
   – Power-on to Ready:200 ms (typical)
• Support for Commercial Temperature Range
   – 0°C to +70°C for Operating Commercial
   – -50°C to +100°C for non-Operating (storage)
• Extremely Rugged and Reliable
   – Built-in ECC support corrects 3 Bytes of error per 512 Byte sector
• Intelligent ATA/IDE Controller
   – Built-in microcontroller with intelligent firmware
   – Built-in Embedded Flash File System
• Power Management Unit
   – Immediate disabling of unused circuitry

Acquired by Texas Instruments on September 23rd, 2011.

3-TERMINAL VOLTAGE REGULATOR, -37 VOLTS < VO < -1.25 VOLTS AT 0.5A GUARANTEED TO 30k rd(Si) TESTED TO MIL-STD-883, METHOD 1019

General Description
The LM137H is an adjustable 3-terminal negative voltage regulator capable of supplying in excess of -0.5A over an output voltage range of -1.2V to -37V. This regulator is exceptionally easy to apply, requiring only 2 external resistors to set the output voltage and 1 output capacitor for frequency compensation. The circuit design has been optimized for excellent regulation and low thermal transients. Futher, the LM137H features internal current limiting, thermal shutdown and safe-area compensation, making it virtually blowout-proof against overloads.

Features
- Output voltage adjustable from -1.2V to -37V
- 0.5A output current guaranteed, -55 C to +150 C
- Line regulation typically 0.01%/V
- Load regulation typically 0.3%
- Excellent thermal regulation, 0.002%/W
- 50 ppm/ C temperature coefficient
- Temperature-independent current limit
- Internal thermal overload protection
- Stantard 3-lead transistor package
- Output short circuit protected