Qdatasheet_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

P/N + Description + Content Search

Searchword :
Part Name(s) : AD8279
AD
Analog Devices
Description : Low Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2

GENERAL DESCRIPTION
The AD8279 consists of two general-purpose Difference amplifiers intended for precision signal conditioning in power critical applications that require both high performance and Low power. The AD8279 provides exceptional common-mode rejection ratio (80 dB) and high bandwidth while amplifying signals well beyond the Supply rails. The on-chip resistors are laser-trimmed for excellent gain accuracy and high CMRR. They also have extremely Low gain drift vs. temperature.

FEATURES
   Wide input range beyond supplies
   Rugged input overvoltage protection
   Low Supply current: 200 μA maximum
   Low power dissipation: 0.5 mW at VS = 2.5 V
   Bandwidth: 1 MHz (G = ½)
   CMRR: 80 dB minimum, dc to 20 kHz (G = ½)
   Low offset voltage drift: ±2 μV/°C maximum (B Grade)
   Low gain drift: 1 ppm/°C maximum (B Grade)
   Enhanced slew rate: 1.4 V/μs
   Wide power Supply range:
      Single Supply: 2 V to 36 V
      Dual supplies: ±2 V to ±18 V

APPLICATIONS
   Voltage measurement and monitoring
   Current measurement and monitoring
   Instrumentation amplifier building block
   Portable, battery-powered equipment
   Test and measurement

Description : Low Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2

GENERAL DESCRIPTION
The AD8278 is a general-purpose Difference amplifier intended for precision signal conditioning in power critical applications that require both high performance and Low power. The AD8278 provides exceptional common-mode rejection ratio (80 dB) and high bandwidth while amplifying signals well beyond the Supply rails. The on-chip resistors are laser-trimmed for excellent gain accuracy and high CMRR. They also have extremely Low gain drift vs. temperature.

FEATURES
   Wide input range beyond supplies
   Rugged input overvoltage protection
   Low Supply current: 200 μA maximum
   Low power dissipation: 0.5 mW at VS = 2.5 V
   Bandwidth: 1 MHz (G = ½)
   CMRR: 80 dB minimum, dc to 20 kHz (G = ½)
   Low offset voltage drift: ±2 μV/°C maximum (B Grade)
   Low gain drift: 1 ppm/°C maximum (B Grade)
   Enhanced slew rate: 1.4 V/μs
   Wide power Supply range:
      Single Supply: 2 V to 36 V
      Dual supplies: ±2 V to ±18 V
   8-lead SOIC and MSOP packages

APPLICATIONS
   Voltage measurement and monitoring
   Current measurement and monitoring
   Instrumentation amplifier building block
   Portable, battery-powered equipment
   Test and measurement

Description : Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifiers

GENERAL DESCRIPTION
The AD8276/AD8277 are general-purpose, unity-gain Difference amplifiers intended for precision signal conditioning in power critical applications that require both high performance and Low power. They provide exceptional common-mode rejection ratio (86 dB) and high bandwidth while amplifying signals well beyond the Supply rails. The on-chip resistors are laser-trimmed for excellent gain accuracy and high CMRR. They also have extremely Low gain drift vs. temperature.
The common-mode range of the amplifiers extends to almost double the Supply voltage, making these amplifiers ideal for single Supply applications that require a high common-mode voltage range. The internal resistors and ESD circuitry at the inputs also provide overvoltage protection to the op amps.

FEATURES
   Wide input range beyond supplies
   Rugged input overvoltage protection
   Low Supply current: 200 μA maximum per channel
   Low power dissipation: 0.5 mW at VS = 2.5 V
   Bandwidth: 550 kHz
   CMRR: 86 dB minimum, dc to 10 kHz
   Low offset voltage drift: ±2 μV/°C maximum (B Grade)
   Low gain drift: 1 ppm/°C maximum (B Grade)
   Enhanced slew rate: 1.1 V/μs
   Wide power Supply range:
      Single Supply: 2 V to 36 V
      Dual supplies: ±2 V to ±18 V

APPLICATIONS
   Voltage measurement and monitoring
   Current measurement and monitoring
   Differential output instrumentation amplifier
   Portable, battery-powered equipment
   Test and measurement

Part Name(s) : AD817ANZ
ADI
Analog Devices
Description : High Speed, Low Power Wide Supply Range Amplifier

PRODUCT DESCRIPTION
The AD817 is a Low Cost, Low Power, single/dual Supply, high speed op amp which is ideally suited for a broad spectrum of signal conditioning and data acquisition applications. This breakthrough product also features high output current drive capability and the ability to drive an unlimited capacitive load while still maintaining excellent signal integrity.
The 50 MHz unity gain bandwidth, 350 V/µs slew rate and settling time of 45 ns (0.1%) make possible the processing of high speed signals common to video and imaging systems. Further more, professional video performance is attained by offering differential gain & phase errors of 0.04% & 0.08° @ 3.58 MHz and 0.1 dB flatness to 70 MHz (gain = +1).
The AD817 is fully specified for operation with a single +5 V power Supply and with dual supplies from ±5 V to ±15 V. This power Supply flexibility, coupled with a very Low Supply current of 7.5 mA and excellent ac characteristics under all power Supply conditions, make the AD817 the ideal choice for many demanding yet power sensitive applications.

FEATURES
   Low Cost
   High Speed
      50 MHz Unity Gain Bandwidth
      350 V/ms Slew Rate
      45 ns Settling Time to 0.1% (10 V Step)
   Flexible Power Supply
      Specified for Single (+5 V) and
         Dual (65 V to 615 V) Power Supplies
      Low Power: 7.5 mA max Supply Current
   High Output Drive Capability
      Drives Unlimited Capacitive Load
      50 mA Minimum Output Current
   Excellent Video Performance
      70 MHz 0.1 dB Bandwidth (Gain = +1)
      0.04% & 0.088 Differential Gain & Phase Errors
         @ 3.58 MHz
   Available in 8-Pin SOIC and 8-Pin Plastic Mini-DIP

Part Name(s) : AD622ARZ-R7
ADI
Analog Devices
Description : Low Cost Instrumentation Amplifier

GENERAL DESCRIPTION
The AD622 is a Low Cost, moderately accurate instrumentation amplifier that requires only one external resistor to set any gain between 2 and 1000. For a gain of 1, no external resistor is required. The AD622 is a complete Difference or subtracter amplifier system that also provides superior linearity and common-mode rejection by incorporating precision laser-trimmed resistors.

FEATURES
    Easy to use
    Low Cost solution
    Higher performance than two or three op amp design
    Unity gain with no external resistor
    Optional gains with one external resistor (Gain range: 2 to 1000)
    Wide power Supply range: ±2.6 V to ±15 V
    Available in 8-lead PDIP and 8-lead SOIC_N packages
    Low Power, 1.5 mA maximum Supply current
    DC performance 0.15% gain accuracy: G = 1 125 μV maximum input offset voltage 1.0 μV/°C maximum input offset drift 5 nA maximum input bias current 66 dB minimum common-mode rejection ratio: G = 1
    Noise 12 nV/√Hz @ 1 kHz input voltage noise 0.60 μV p-p noise: 0.1 Hz to 10 Hz, G = 10
    AC characteristics 800 kHz bandwidth: G = 10 10 μs settling time to 0.1% @ G = 1 to 100 1.2 V/μs slew rate

APPLICATIONS
    Transducer interface
    Low Cost thermocouple amplifier
    Industrial process controls
    Difference amplifier
    Low Cost data acquisition

Description : Wide Supply Range, Rail-to-Rail Output Instrumentation Amplifier

GENERAL DESCRIPTION
The AD8426 is a dual-channel, Low Cost, Wide Supply range instrumentation amplifier that requires only one external resistor to set any gain from 1 to 1000.
The AD8426 is designed to work with a variety of signal voltages. A Wide input range and rail-to-rail output alLow the signal to make full use of the Supply rails. Because the input range can also go beLow the negative Supply, small signals near ground can be amplified without requiring dual supplies. The AD8426 operates on supplies ranging from ±1.35 V to ±18 V for dual supplies and 2.2 V to 36 V for a single Supply.
The robust AD8426 inputs are designed to connect to real world sensors. In addition to its Wide operating Range, the AD8426 can handle voltages beyond the rails. For example, with a ±5 V Supply, the part is guaranteed to withstand ±35 V at the input with no damage. Minimum and maximum input bias currents are specified to facilitate open-wire detection.

FEATURES
   2 channels in a small, 4 mm × 4 mm LFCSP
   LFCSP package has no metal pad
      More routing room
      No current leakage to pad
   Gain set with 1 external resistor
      Gain range: 1 to 1000
   Input voltage goes beLow ground
   Inputs protected beyond supplies
   Very Wide power Supply range
      Single Supply: 2.2 V to 36 V
      Dual Supply: ±1.35 V to ±18 V
   Bandwidth (G = 1): 1 MHz
   CMRR (G = 1): 80 dB minimum
   Input noise: 24 nV/√Hz
   Typical Supply current (per amplifier): 350 μA
   Specified temperature range: −40°C to +125°C
  
APPLICATIONS
   Industrial process controls
   Bridge amplifiers
   Medical instrumentation
   Portable data acquisition
   Multichannel systems

Linear
Linear Technology
Description : 3.3V Single Supply Video Difference Amplifier

DESCRIPTION
The LT®6552 is a video Difference amplifier optimized for Low voltage single Supply operation. This versatile amplifier features uncommitted high input impedance (+) and (–) inputs and can be used in differential or single-ended configurations. A second set of inputs gives gain adjustment and DC control to the differential amplifier.

FEATURES
■ Differential or Single-Ended Gain Block
Wide Supply Range 3V to 12.6V
■ Output Swings Rail-to-Rail
■ Input Common Mode Range Includes Ground
■ 600V/µs Slew Rate
■ –3dB Bandwidth = 75MHz, AV = ±2
■ CMRR at 10MHz: >60dB
■ Specified on 3.3V, 5V and ±5V Supplies
■ High Output Drive: ±70mA
■ Power Shutdown to 300µA
■ Operating Temperature Range: –40°C to 85°C
■ Available in 8-Lead SO and Tiny 3mm x 3mm x 0.8mm DFN Packages

APPLICATIONS
■ Differential to Single-Ended Conversion
■ Video Line Driver
■ Automotive Displays
■ RGB Amplifiers
■ Coaxial Cable Drivers
Low Voltage High Speed Signal Processing

ADI
Analog Devices
Description : Wide Supply Range, MicroPower, Rail-to-Rail Instrumentation Amplifier

GENERAL DESCRIPTION
The AD8420 is a Low Cost, microPower, Wide Supply Range, instrumentation amplifier with a rail-to-rail output and a novel architecture that alLows for extremely flexible design. It is optimized to amplify small differential voltages in the presence of large common-mode signals.
The AD8420 is based on an indirect current feedback architecture that gives it an excellent input common-mode range. Unlike conventional instrumentation amplifiers, the AD8420 can easily amplify signals at or even slightly beLow ground without requiring dual supplies. The AD8420 has rail-to-rail output, and the output voltage swing is completely independent of the input common mode voltage.

FEATURES
   Maximum Supply current: 90 μA
   Minimum CMRR: 100 dB
   Drives heavy capacitive loads: ~700 pF
   Rail-to-rail output
   Input voltage range goes beLow ground
   Gain set with 2 external resistors
      Can achieve Low gain drift at any gain
   Very Wide power Supply range
      Single Supply: 2.7 V to 36 V
      Dual Supply: ±2.7 V to ±18 V
   Bandwidth (G = 100): 2.5 kHz
   Input voltage noise: 55 nV/√Hz
   High dc precision
      Maximum offset voltage: 125 μV
      Maximum offset drift: 1 μV/°C
   Maximum differential input voltage: ±1 V
   8-lead MSOP package

APPLICATIONS
   Bridge amplifiers
   Pressure measurement
   Medical instrumentation
   Portable data acquisition
   Multichannel systems

Part Name(s) : STI5512
ETC1
Unspecified
Description : VCXO 27.000 MHz / HIGH RELIABILITY FOR Low Cost Wide FREQUENCY RANGE

FEATURES
1. HIGH RELIABILITY FOR Low Cost
2. Wide FREQUENCY RANGE
3. FREQUENCY STABILITY OF +-10 PPM AVAILABLE
4. AVAILABLE IN 5.0 AND 3.3 VOLT
5. CHEAPEST AVAILABLE LEADED VCXO

Part Name(s) : AD8202WYRMZ AD8202WYRZ
ADI
Analog Devices
Description : High Common-Mode Voltage, Single-Supply Difference Amplifier

GENERAL DESCRIPTION
The AD8202 is a single-Supply Difference amplifier for amplifying and Low-pass filtering small differential voltages in the presence of a large common-mode voltage (CMV). The input CMV range extends from −6 V to +28 V at a typical Supply voltage of 5 V.
   
FEATURES
    High common-mode voltage range
        −6 V to +28 V at a 5 V Supply voltage
    Operating temperature range: −40°C to +125°C
    Supply voltage range: 3.5 V to 12 V
    Low-pass filter (1-pole or 2-pole)
    Excellent ac and dc performance
        ±1 mV voltage offset
        ±1 ppm/°C typical gain drift
        80 dB CMRR min dc to 10 kHz
    Qualified for automotive applications
   
APPLICATIONS
    Transmission control
    Diesel injection control
    Engine management
    Adaptive suspension control
    Vehicle dynamics control
   

12345678910 Next


All Rights Reserved © qdatasheet.com [ Privacy Policy ] [ Contact Us ]