AT90S2313 View Datasheet(PDF) - Atmel Corporation
Part Name
Description
MFG CO.
'AT90S2313' PDF : 92 Pages View PDF
Electrical Characteristics
Absolute Maximum Ratings*
Operating Temperature.................................. -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin Except RESET
with Respect to Ground ...............................-1.0V to VCC+0.5V
Voltage on RESET with Respect to Ground ....-1.0V to +13.0V
Maximum Operating Voltage ............................................ 6.6V
DC Current per I/O Pin ............................................... 40.0 mA
DC Current VCC and GND Pins ................................ 200.0 mA
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
DC Characteristics
TA = -40°C to 85°C, VCC = 2.7V to 6.0V (unless otherwise noted)
Symbol Parameter
Condition
VIL
Input Low Voltage
(Except XTAL1)
VIL1
Input Low Voltage
(XTAL1)
VIH
Input High Voltage
(Except XTAL1, RESET)
VIH1
Input High Voltage
(XTAL1)
VIH2
Input High Voltage
(RESET)
VOL
Output Low Voltage(3)
(Ports B, D)
IOL = 20 mA, VCC = 5V
IOL = 10 mA, VCC = 3V
VOH
Output High Voltage(4)
(Ports B, D)
IOH = -3 mA, VCC = 5V
IOH = -1.5 mA, VCC = 3V
IIL
Input Leakage
Current I/O pin
VCC = 6V, pin low
(absolute value)
IIH
Input Leakage
Current I/O pin
VCC = 6V, pin high
(absolute value)
RRST
Reset Pull-up Resistor
RI/O
ICC
ICC
VACIO
IACLK
tACPD
I/O Pin Pull-up Resistor
Power Supply Current
Power-down Mode(5)
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
Active Mode, VCC = 3V, 4 MHz
Idle Mode VCC = 3V, 4 MHz
WDT enabled, VCC = 3V
WDT disabled, VCC = 3V
VCC = 5V
Vin = VCC /2
VCC = 5V
Vin = VCC/2
VCC = 2.7V
VCC = 4.0V
Min
-0.5
-0.5
0.6 VCC(2)
0.7 VCC(2)
0.85 VCC(2)
4.3
2.3
100.0
35.0
-50.0
Typ
9.0
<1.0
750.0
500.0
Max
0.3 VCC(1)
0.3 VCC(1)
VCC + 0.5
VCC + 0.5
VCC + 0.5
0.6
0.5
1.5
Units
V
V
V
V
V
V
V
V
V
µA
980.0
nA
500.0
kΩ
120.0
kΩ
3.0
mA
1.0
mA
15.0
µA
2.0
µA
40.0
mV
50.0
nA
ns
72 AT90S2313
0839I–AVR–06/02
Share Link: 
