EVAL-AD7763EB View Datasheet(PDF) - Analog Devices

Part Name

Description

MFG CO.

EVAL-AD7763EB

24-Bit, 625 kSPS, 109 dB Σ-Δ ADC with On-Chip Buffers, Serial Interface

Analog Devices 

1 2 3 4 5 6 7 8 9 10 Next

Data Sheet

Pin No.

8

30

17

37

3

2

36

38

39, 40, 45

46 to 48

49

50

51

52

54

55

56

58

60

61

AD7763

Mnemonic

DECAPA

DECAPB

RBIAS

RESET

MCLK

MCLKGND

SYNC

DRDY

SH2:0

ADR2:0

SCP

SDL

FSI

SDI

SDO

SCO

FSO

CDIV

SCR

I2S

EPAD

Description

Decoupling Pin. A 100 nF capacitor must be inserted between this pin and AGND1.

Decoupling Pin. A 33 pF capacitor must be inserted between this pin and AGND3.

Bias Current Setting. A resistor must be inserted between this pin and AGND.

See the Bias Resistor Selection section.

A falling edge on this pin resets all internal digital circuitry. Holding this pin low

keeps the AD7763 in a reset state.

Master Clock Input. A low jitter digital clock must be applied to this pin. The output data rate

depends on the frequency of this clock. See the Clocking the AD7763 section.

Master Clock Ground Sensing Pin.

Synchronization Input. A falling edge on this pin resets the internal filter. This can be used

to synchronize multiple devices in a system.

Data Ready Output. Each time new conversion data is available, an active low pulse,

½ ICLK period wide, is produced on this pin. See the AD7763 Interface section.

Share Pins 2:0. For multiple AD7763 devices sharing a common serial bus. Each device is wired

with the binary value that represents the number of devices sharing the serial bus. SH2 is the

MSB. See the Sharing the Serial Bus section.

Address 2:0. Allows multiple AD7763 devices to share a common serial bus. Each device must be

programmed with an individual address using these three pins. See the Sharing the Serial Bus

section.

Serial Clock Polarity. Determines on which edge of SCO the data bits are clocked out and on

which edge they are valid. All timing diagrams are shown with SCP = 0, and all SCO edges

shown should be inverted for SCP = 1.

Serial Data Latch. A pulse is output on this pin after every 16 data bits. The pulse is one SCO

period wide and can be used in conjunction with FSO as an alternative framing method for

serial transfers requiring a framing signal more frequent than every 32 bits.

Frame Sync In. The status of this pin is checked on the falling edge of SCO. If this pin is low, then

the first data bit is latched in on the next SCO falling edge when SCP = 0 or on the rising edge of

SCO if SCP = 1.

Serial Data In. The first data bit (MSB) must be valid on the next SCO falling edge when SCP = 0

(or SCO rising edge SCP = 1) after the FSI event has been latched. Each write requires 32 bits: the

ALL bit, 3 address bits, and 12 register address bits, followed by the remaining 16 bits of data to

be written to the device.

Serial Data Out. Address, status, and data bits are clocked out on this line during each serial

transfer.

If SCP = 0, each bit is clocked out on an SCO rising edge and is valid on the falling edge. When

the I2S pin is set to logic high, this pin outputs the signal defined as SD in the I2S bus

specification. See the Reading Data Using the I2S Interface section for details.

Serial Clock Out. This clock signal is derived from the internal ICLK signal. The frequency of SCO

is equal to either ICLK or ICLK/2, depending on the state of the CDIV and SCR pins (see the

AD7763 Interface section). When the I2S pin is logic high, this pin outputs the signal defined as

SCK by the I2S bus specification. See the Reading Data Using the I2S Interface section.

Frame Sync Out. This signal frames the serial data output and is 32 SCO periods wide. The

exception to the framing behavior of FSO occurs in decimate × 32 mode, where, for certain

combinations of CDIV and SCR, the FSO signal is constantly logic low. See the Reading Data

Using the SPI Interface section. When the I2S pin is set to logic high, this pin outputs the signal

defined as WS in the I2S bus specification. See the Reading Data Using the I2S Interface section.

Clock Divider. This pin is used to select the ratio of MCLK to ICLK. See the AD7763 Interface

section.

Serial Clock Rate. This pin and the CDIV pin program the SCO frequency (see Table 7).

I2S Select. A Logic 1 on this pin changes the serial data-out mode from SPI to I2S. The SDO pin

outputs as the SD signal, the SCO pin outputs the SCK signal, and the FSO pin outputs the WS

signal. When writing to the AD7763, the I2S pin is set to logic low and the SPI interface is used.

See the Reading Data Using the I2S Interface section for further details.

Exposed Pad. Connect the exposed pad to AGNDx with six to eight vias.

Rev. B | Page 9 of 32

Share Link: