EVAL-ADG824EBZ View Datasheet(PDF) - Analog Devices
Part Name
Description
MFG CO.
'EVAL-ADG824EBZ' PDF : 16 Pages View PDF
ADG824
SPECIFICATIONS
VDD = 2.7 V to 3.6 V, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On Resistance Match Between
Channels, ∆RON
On Resistance Flatness, RFLAT (ON)
+25°C
0.5
0.65
0.003
0.13
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
±0.2
±0.2
0.005
Digital Input Capacitance, CIN
2.7
DYNAMIC CHARACTERISTICS1
tON
7
9.5
tOFF
6
7.7
Break-Before-Make Time Delay, tBBM 3.5
Charge Injection, QINJ
27
Off Isolation
−71
Channel-to-Channel Crosstalk
−90
−40°C to +85°C
0 to VDD
0.7
0.01
0.2
1.3
0.8
±0.1
10.8
8.6
2
−67
Total Harmonic Distortion, THD + N 0.06
Insertion Loss
−0.05
−3 dB Bandwidth
90
CS (Off )
25
CD, CS (On)
58
POWER REQUIREMENTS
IDD
0.003
1
1 Guaranteed by design; not subject to production test.
Unit
Test Conditions/Comments
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
nA typ
nA typ
VDD = 2.7 V, VS = 0 V to VDD, IDS = 100 mA; see Figure 19
VDD = 2.7 V, VS = 0.65 V, IDS = 100 mA
VDD = 2.7 V, VS = 0 V to VDD, IDS = 100 mA
VDD = 3.6 V
VS = 0.6 V/3.3 V, VD = 3.3 V/0.6 V; see Figure 20
VS = VD = 0.6 V or 3.3 V; see Figure 21
V min
V max
μA typ
μA max
pF typ
VIN = VINL or VINH
VIN = VINL or VINH
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
dB typ
%
dB typ
MHz typ
pF typ
pF typ
μA typ
μA max
RL = 50 Ω, CL = 35 pF
VS = 2 V/0 V; see Figure 22
RL = 50 Ω, CL = 35 pF
VS = 2 V; see Figure 22
RL = 50 Ω, CL = 35 pF
VS1 = VS2 = 2 V; see Figure 23
VS = 1.5 V, RS = 0 Ω, CL = 1 nF; see Figure 24
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 25
S1A to S2A/S1B to S2B, RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 26
S1A to S1B/S2A to S2B, RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 27
RL = 33 Ω, f = 20 Hz to 20 kHz, VS = 2 V p-p
RL = 50 Ω, CL = 5 pF; see Figure 28
RL = 50 Ω, CL = 5 pF; see Figure 28
VDD = 3.6 V
Digital inputs = 0 V or 3.6 V
Rev. 0 | Page 3 of 16
Share Link: 
