HCPL-2530-360E View Datasheet(PDF) - Avago Technologies
Part Name
Description
MFG CO.
'HCPL-2530-360E' PDF : 14 Pages View PDF
Notes:
1. Each channel.
2. CURRENT TRANSFER RATIO is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%.
3. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
4. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
5. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode
pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level
is the maximum tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal, VCM, to assure that the output will remain
in a Logic Low state (i.e., VO < 0.8 V).
6. The 1.9 k: load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
7. The 4.1 k: load represents 1 LSTTL unit load of 0.36 mA and the 6.1 kΩ pull-up resistor.
8. The frequency at which the ac output voltage is 3 dB below the low frequency asymptote.
9. Use of a 0.1 PF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for 1 second (leakage detec-
tion current limit, II-O ≤5 PA).
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for 1 second (leakage detec-
tion current limit, II-O ≤5 PA).
12. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
13. Derate linearly above 90°C free-air temperature at a rate of 3.0 mW/ °C for the SOIC-8 package.
TA = 25°C
10 VCC = 5.0 V
40 mA
35 mA
30 mA
25 mA
5
20 mA
15 mA
10 mA
IF = 5 mA
0
0
10
20
VO – OUTPUT VOLTAGE – V
1.5
HCPL-2530/0530
HCPL-2531/0531/4534/0534
1.0
0.5
0.1
0
NORMALIZED
IF = 16 mA
VO = 0.5 V
VCC = 5 V
TA = 25°C
1
10
100
IF – INPUT CURRENT – mA
1000
100
IF
10
+
VF
–
1.0
TA = 25°C
0.1
0.01
0.001
1.1 1.2 1.3 1.4 1.5 1.6
VF – FORWARD VOLTAGE – VOLTS
Figure 1. DC and pulsed transfer characteristics. Figure 2. Current transfer ratio vs. input current. Figure 3. Input current vs. forward voltage.
1.1
1.0
0.9
NORMALIZED
IF = 16 mA
0.8
VO = 0.5 V
VCC = 5 V
TA = 25°C
0.7
HCPL-2530/0530
HCPL-2531/0531/4534/0534
0.6
-60 -40 -20 0 20 40 60 80 100
TA – TEMPERATURE – °C
2000
1500
IF = 16 mA, VCC = 5.0 V
HCPL-2530/0530 (RL = 4.1 kΩ)
HCPL-2531/0531/4534/0534
(RL = 1.9 kΩ)
1000
500
tPLH tPHL
0
-60
-20
20
60
100
TA – TEMPERATURE – °C
10+4
10+3
IF = 0
VO = VCC = 5.0 V
10+2
10+1
10 0
10 -1
10 -2
-50 -25 0 +25 +50 +75 +100
TA – TEMPERATURE – °C
Figure 4. Current transfer ratio vs. temperature. Figure 5. Propagation delay vs. temperature.
Figure 6. Logic high output current vs. tempera-
ture.
12
Share Link: 
