ICS1893CYI-10LF View Datasheet(PDF) - Integrated Circuit Systems
Part Name
Description
MFG CO.
'ICS1893CYI-10LF' PDF : 143 Pages View PDF
ICS1893CY-10 Data Sheet - Release
Chapter 7 Management Register Set
7.2.5 Low Power Mode (bit 0.11)
This bit provides one way to control the ICS1893CY-10 low-power mode function. When bit 0.11 is logic:
• Zero, there is no impact to ICS1893CY-10 operations.
• One, the ICS1893CY-10 enters the low-power mode. In this case, the ICS1893CY-10 disables all internal
functions and drives all MAC/repeater output pins low except for those that support the MII Serial
Management Port. In addition, the ICS1893CY-10 internally activates the TPTRI function to tri-state the
signals on the Twisted-Pair Transmit pins (TP_TXP and TP_TXN) and achieve additional power savings.
Note:
There are two ways the ICS1893CY-10 can enter low-power mode. When entering low-power
mode:
• By setting bit 0.11 to logic one, the ICS1893CY-10 maintains the value of all Management
Register bits except the latching high (LH) and latching low (LL) status bits, which are
re-initialized to their default values instead. (For more information on latching high and latching
low bits, see Section 7.1.4.1, “Latching High Bits” and Section 7.1.4.2, “Latching Low Bits”.)
• During a reset, the ICS1893CY-10 sets all management register bits to their default values.
7.2.6 Isolate (bit 0.10)
This bit controls the ICS1893CY-10 Isolate function. When bit 0.10 is logic:
• Zero, there is no impact to ICS1893CY-10 operations.
• One, the ICS1893CY-10 electrically isolates its data paths from the MAC/Repeater Interface. The
ICS1893CY-10 places all MAC/repeater output signals (TXCLK, RXCLK, RXDV, RXER, RXD[3:0], COL,
and CRS) in a high-impedance state and it isolates all MAC/repeater input signals (TXD[3:0], TXEN, and
TXER). In this mode, the Serial Management Interface continues to operate normally (that is, bit 0.10
does not affect the Management Interface).
The default value for bit 0.10 depends upon the PHY address of Table 7-16. If the PHY address:
• Is equal to 00000b, then the default value of bit 0.10 is logic one, and the ICS1893CY-10 isolates itself
from the MAC/Repeater Interface.
• Is not equal to 00000b, then the default value of bit 0.10 is logic zero, and the ICS1893CY-10 does not
isolate its MAC/Repeater Interface.
7.2.7 Restart Auto-Negotiation (bit 0.9)
This bit allows an STA to restart the auto-negotiation process in Software mode (that is, the HW/SW pin is
logic one). When bit 0.12 is logic:
• Zero, the Auto-Negotiation sublayer is disabled, and the ICS1893CY-10 isolates any attempt by the STA
to set bit 0.9 to logic one.
• One (as set by an STA), the ICS1893CY-10 restarts the auto-negotiation process. Once the
auto-negotiation process begins, the ICS1893CY-10 automatically sets this bit to logic zero, thereby
providing the self-clearing feature.
ICS1893CY-10 Rev 1/07
Copyright © 2007, Integrated Device Technology, Inc.
All rights reserved.
62
Share Link: 
