ISP1106DHTM View Datasheet(PDF) - Ericsson
Part Name
Description
MFG CO.
'ISP1106DHTM' PDF : 25 Pages View PDF
ISP1105/1106
Advanced USB transceivers
11. Static characteristics
Table 13. Static characteristics: supply pins
VCC = 4.0 V to 5.5 V or Vreg(3.3) = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; VGND = 0 V; see Table 10 for valid voltage level
combinations; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Unit
Vreg(3.3)
ICC
regulated supply voltage internal regulator option;
[1][2] 3.0
3.3
3.6
V
output
Iload ≤ 300 μA
operating supply current
full-speed transmitting and
[3] -
4
8
mA
receiving at 12 Mbit/s; CL = 50 pF
on D+/D−
ICC(I/O)
operating I/O supply current full-speed transmitting and
receiving at 12 Mbit/s
[3] -
1
2
mA
ICC(idle)
supply current during
full-speed idle: VD+ > 2.7 V,
[4] -
-
500
μA
full-speed idle and SE0
VD− < 0.3 V; SE0: VD+ < 0.3 V,
VD− < 0.3 V
ICC(I/O)(static) static I/O supply current
full-speed idle, SE0 or suspend
-
-
20
μA
ICC(susp)
suspend supply current
SUSPND = HIGH
[4] -
-
20
μA
ICC(dis)
disable mode supply current VCC(I/O) not connected
[4] -
-
20
μA
ICC(I/O)(sharing) sharing mode I/O supply
VCC(5.0) or Vreg(3.3) not connected
-
-
20
μA
current
IDx(sharing)
sharing mode load current VCC(5.0) or Vreg(3.3) not connected;
-
-
10
μA
on pins D+ and D−
SOFTCON = LOW; VDx = 3.6 V
Vreg(3.3)th
regulated supply voltage
detection threshold
1.65 V ≤ VCC(I/O) ≤ Vreg(3.3);
2.7 V ≤ Vreg(3.3) ≤ 3.6 V
supply lost
-
-
0.8
V
supply present
[5] 2.4
-
-
V
Vreg(3.3)hys
regulated supply voltage
detection hysteresis
VCC(I/O) = 1.8 V
-
0.45 -
V
VCC(I/O)th
I/O supply voltage detection Vreg(3.3) = 2.7 V to 3.6 V
threshold
supply lost
-
-
0.5
V
supply present
1.4
-
-
V
VCC(I/O)hys
I/O supply voltage detection Vreg(3.3) = 3.3 V
hysteresis
-
0.45 -
V
[1] Iload includes the pull-up resistor current via pin Vpu(3.3).
[2] In ‘suspend’ mode, the minimum voltage is 2.7 V.
[3] Maximum value is characterized only, not tested in production.
[4] Excluding any load current and Vpu(3.3)/Vsw source current to the 1.5 kΩ and 15 kΩ pull-up and pull-down resistors (200 μA typ.).
[5] When VCC(I/O) < 2.7 V, the minimum value for Vth(reg3.3)(present) is 2.0 V.
ISP1105_1106_10
Product data sheet
Rev. 10 — 28 September 2009
© ST-ERICSSON 2009. All rights reserved.
12 of 25
Share Link: 
