LTC1560-1IS8 View Datasheet(PDF) - Linear Technology
Part Name
Description
MFG CO.
'LTC1560-1IS8' PDF : 8 Pages View PDF
LTC1560-1
ABSOLUTE MAXIMUM RATINGS
Total Supply Voltage (V + to V –) ............................. 12V
Power Dissipation............................................. 400mW
Burn-In Voltage ................................................... ±5.5V
Operating Temperature Range
LTC1560-1C ........................................... 0°C to 70°C
LTC1560-1I ....................................... – 40°C to 85°C
Maximum Junction Temperature ......................... 150°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
PACKAGE/ORDER INFORMATION
TOP VIEW
GND 1
VIN 2
GND 3
V– 4
8 VOUT
7 SHDN
6 V+
5 0.5fC/fC
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 125°C/ W
Consult factory for Military grade parts.
ORDER PART
NUMBER
LTC1560-1CS8
LTC1560-1IS8
S8 PART MARKING
15601
15601I
ELECTRICAL CHARACTERISTICS
VS = ±5V, TA = 25°C, Pin 5 = – 5V (fCUTOFF = 1MHz), Pin 7 = 0V unless otherwise specified.
PARAMETER
CONDITIONS
Operating Supply Voltage Range
Passband Gain (fCUTOFF = 1MHz)
VIN = 0.5VRMS, fIN = 20kHz
fIN = 100kHz
q
fIN = 300kHz
fIN = 550kHz (Gain Relative to 100kHz)
q
fIN = 850kHz (Gain Relative to 100kHz)
q
fIN = 950kHz (Gain Relative to 100kHz)
q
fIN = fCUTOFF = 1MHz (Gain Relative to 100kHz) q
Transition Band Gain (Note 1)
VIN = 0.5VRMS, fIN = 1.4MHz
q
fIN = 1.9MHz
fIN = 2.0MHz
Stopband Gain (fCUTOFF = 1MHz) (Note 2)
fIN = 2.44MHz
q
fIN = 3.0MHz
fIN = 6.0MHz
Passband Gain (fCUTOFF = 500kHz)
fIN = 100kHz, Pin 5 = 5V
fIN = fCUTOFF = 500kHz
q
fIN = 1.4MHz
Output Voltage Swing
RL = 5k
q
Output DC Offset (VOS)
Power Supply Current (IS)
q
Power Supply Current in Shutdown Mode Pin 7 at 5V
Total Output Noise
Total Harmonic Distortion (THD)
Input Resistance (RIN)
VIN (Pin 2) Tied to Ground, fCUTOFF = 1MHz, BW = 2MHz
VIN (Pin 2) Tied to Ground, fCUTOFF = 0.5MHz, BW = 1MHz
VIN = 1VRMS, fIN = 200kHz, fCUTOFF = 1MHz, BW = 1MHz
fIN = 300kHz, fCUTOFF = 1MHz, BW = 1MHz
fIN = 1MHz, fCUTOFF = 1MHz, BW = 2MHz
fIN = 300kHz, fCUTOFF = 0.5MHz, BW = 1MHz
fIN = 500kHz, fCUTOFF = 0.5MHz, BW = 1MHz
q
MIN TYP MAX
±4.5 ±5.0 ±5.5
0.17
– 0.3 0.18 0.6
0.08
– 0.35 0.05 0.3
– 0.8 – 0.3 0
– 3.0 0.6 0.5
– 5.0 – 1.0 1.0
– 24 –18
– 42
– 51
– 70 – 65
– 68
– 66.1
0.14
– 4 – 1.6 0.5
– 45
±1.9 ±3
±250
22 29
1
350
322
– 63
– 61
– 62
– 62
– 63
6
8
10
UNITS
V
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
V
mV
mA
mA
µVRMS
µVRMS
dB
dB
dB
dB
dB
kΩ
The q denotes specifications which apply over the full operating
temperature range.
Note 1: To properly measure high frequency characteristics of the filter, a
noninverting output buffer is recommended as shown on the demo board
connection diagram, Figure 2. A small resistor (e.g. 100Ω) can also be
used instead of the buffer to isolate any high capacitive load (CL > 10pF)
from the filter output.
Note 2: The stopband gain at 2.44MHz is guaranteed by design.
2
Share Link: 
