PC929J00000F View Datasheet(PDF) - Sharp Electronics
Part Name
Description
MFG CO.
PC929J00000F
Sharp Electronics
'PC929J00000F' PDF : 22 Pages View PDF
■ Absolute Maximum Ratings
(unless otherwise specified Ta=Topr)
Parameter
Symbol Rating
Unit
*1Forward current
IF
20
mA
*2Reverse voltage
VR
6
V
Supply voltage
VCC
35
V
O1 output current
IO1
0.1
A
*3O1 peak output current IO1P
0.4
A
O2 output current
IO2
0.1
A
*3O2 peak output current IO2P
0.4
A
O1 output voltage
VO1
*4Power dissipation
PO
35
V
500
mW
Overcurrent detection voltage VC
VCC
V
Overcurrent detection current IC
30
mA
Error signal output voltage VFS
VCC
V
Error signal output current IFS
20
mA
*5Total power dissipation
Ptot
550
mW
*6Isolation voltage
Viso (rms)
4.0
kV
Operating temperature
Topr −25 to +80 ˚C
Storage temperature
*7Soldering temperature
Tstg −55 to +125 ˚C
Tsol
260
˚C
*1 The derating factors of a absolute maximum ratings due to ambient temperature
are shown in Fig.15
*2 Ta =25˚C
*3 Pulse width≤0.15µs, Duty ratio : 0.01
*4.5 The derating factors of a absolute maximum ratings due to ambient temperature
are shown in Fig.16
*6 AC for 1minute, 40 to 60 %RH, Ta =25˚C, f=60Hz
*7 For 10s
PC929J00000F Series
■ Electro-optical Characteristics
Parameter
Symbol
Conditions *8
(unless otherwise specified Ta=Topr)
MIN. TYP. MAX. Unit
Forward voltage
VF1
Ta=25˚C, IF=10mA
−
1.6 1.75 V
VF2
Ta=25˚C, IF=0.2mA
1.2 1.5
−
V
Reverse current
IR
Ta=25˚C, VR=5V
−
−
10
µA
Terminal capacitance
Ct
Ta=25˚C, V=0, f=1kHz
−
30 250 pF
Supply voltage
O1 Low level output voltage
VCC
Ta=−10 to +60˚C
−
15
−
30
V
15
−
24
V
VO1L VCC1=12V, VCC2=−12V, IO1=0.1A, IF=5mA*9 −
0.2 0.4
V
O2 High level output voltage
VO2H
VCC=VO1=24V, IO2=−0.1A, IF=5mA *9 20
22
−
V
O2 Low level output voltage
VO2L
VCC=24V, IO2=0.1A, IF=0 *9 −
1.2 2.0
V
O1 leak current
IO1L
Ta=25˚C, VCC=VO1=35V, IF=0 *9 −
−
500 µA
High level supply current
ICCH
Ta=25˚C, VCC=VO1=24V, IF=5mA *9 −
VCC=VO1=24V, IF=5mA
*9
−
10
17 mA
−
19 mA
Low level supply current
ICCL
Ta=25˚C, VCC=VO1=24V, IF=0 *9 −
VCC=VO1=24V, IF=0
*9
−
11
18 mA
−
20 mA
*8 It shall connect a by-pass capacitor of 0.01 µF or more between VCC (pin 13 ) and GND (pin, 10 , 14 ) near the device, when it measures the transfer characteristics and the
output side characteristics.
*9 FS=OPEN, VC=0
Sheet No.: D2-A06302EN
4
Share Link: 