PIC16CR58A-04I/SO View Datasheet(PDF) - Microchip Technology
Part Name
Description
MFG CO.
'PIC16CR58A-04I/SO' PDF : 217 Pages View PDF
PIC16C5X
PIC16C54/55/56/57
11.2 DC Characteristics: PIC16C54/55/56/57-RCI, XTI, 10I, HSI, LPI (Industrial)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +85°C
Sym Min Typ(1) Max Units
Conditions
Supply Voltage
PIC16C5X-RCI
PIC16C5X-XTI
PIC16C5X-10I
PIC16C5X-HSI
PIC16C5X-LPI
VDD
3.0
—
6.25 V FOSC = DC to 4 MHz
3.0
—
6.25 V FOSC = DC to 4 MHz
4.5
—
5.5
V FOSC = DC to 10 MHz
4.5
—
5.5
V FOSC = DC to 20 MHz
2.5
—
6.25 V FOSC = DC to 40 kHz
RAM Data Retention Voltage(2) VDR —
1.5*
—
V Device in SLEEP mode
VDD Start Voltage to ensure
Power-On Reset
VPOR —
VSS
—
V See Section 7.4 for details on
Power-On Reset
VDD Rise Rate to ensure
Power-On Reset
SVDD 0.05* —
— V/ms See Section 7.4 for details on
Power-On Reset
Supply Current(3)
PIC16C5X-RCI(4)
PIC16C5X-XTI
PIC16C5X-10I
PIC16C5X-HSI
PIC16C5X-LPI
IDD
—
1.8
3.3 mA FOSC = 4 MHz, VDD = 5.5V
—
1.8
3.3 mA FOSC = 4 MHz, VDD = 5.5V
—
4.8
10 mA FOSC = 10 MHz, VDD = 5.5V
—
4.8
10 mA FOSC = 10 MHz, VDD = 5.5V
—
9.0
20 mA FOSC = 20 MHz, VDD = 5.5V
—
15
40
µA FOSC = 32 kHz, VDD = 3.0V,
WDT disabled
Power Down Current(5)
IPD
—
4.0
14
µA VDD = 3.0V, WDT enabled
—
0.6
12
µA VDD = 3.0V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453B-page 70
Preliminary
© 1998 Microchip Technology Inc.
Share Link: 
