NBSG11BA View Datasheet(PDF) - ON Semiconductor
Part Name
Description
MFG CO.
'NBSG11BA' PDF : 12 Pages View PDF
NBSG11
Table 6. DC CHARACTERISTICS, INPUT WITH RSPECL OUTPUT VCC = 3.3 V; VEE = 0 V (Note 11)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
POWER SUPPLY CURRENT
IEE
Negative Power Supply Current
45
60
75
45
60
75
45
60
75 mA
RSPECL OUTPUTS (Note 12)
VOH
Output HIGH Voltage
VOUTPP Output Voltage Amplitude
2250 2330 2375 2325 2365 2400 2350 2390 2425 mV
350 410 525 350 410 525 350 410 525 mV
DIFFERENTIAL CLOCK INPUTS DRIVEN SINGLE−ENDED (Figures 4 & 6) (Note 13)
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
1200
0
VCC
VIH −
150
1200
0
VCC
VIH −
150
1200
0
VCC mV
VIH − mV
150
Vth
Input Threshold Reference Voltage
950
Range (Note 14)
VCC 950
–75
VCC
950
–75
VCC mV
–75
VISE
Single−Ended Input Voltage (VIH –
150
VIL)
2600 150
2600 150
260 mV
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 5 & 7) (Note 15)
VIHD
VILD
Differential Input HIGH Voltage
Differential Input LOW Voltage
1200
0
VCC
VCC −
75
1200
0
VCC
VCC −
75
1200
0
VCC mV
VCC − mV
75
VID
VIHCMR
Differential Input Voltage
(VIHD – VILD)
Input HIGH Voltage Common Mode
Range (Note 16) (Figure 8)
75
1200
2600 75
3300 1200
2600 75
3300 1200
2600 mV
3300 mV
IIH
Input HIGH Current (@VIH)
IIL
Input LOW Current (@VIL)
80 150
25 100
80
150
25
100
80
150 mA
25
100 mA
TERMINATION RESISTORS
RTIN
Internal Input Termination Resistor
45
50
55
45
50
55
45
50
55
W
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
11. Input and output parameters vary 1:1 with VCC.
12. All loading with 50 W to VCC − 2 V.
13. Vth, VIH, VIL, and VISE parameters must be complied with simultaneously.
14. Vth is applied to the complementary input when operating in single−ended mode. Vth = (VIH − VIL) / 2.
15. VIHD, VILD, VID and VIHCMR parameters must be complied with simultaneously.
16. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differen-
tial input signal.
http://onsemi.com
6
Share Link: 
