5962-9750701HXC View Datasheet(PDF) - Analog Devices
Part Name
Description
MFG CO.
'5962-9750701HXC' PDF : 44 Pages View PDF
AD14060/AD14060L
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE 1149.1 JTAG
test access port of the ADSP-2106x to monitor and control the
target board processor during emulation. The EZ-ICE probe
requires that the AD14060/AD14060L’s CLKIN (optional),
TMS, TCK, TRST, TDI, TDO, EMU and GND signals be
made accessible on the target system via a 14-pin connector (a
pin strip header) such as that shown in Figure 6. The EZ-ICE
probe plugs directly onto this connector for chip-on-board emu-
lation. You must add this connector to your target board design
if you intend to use the ADSP-2106x EZ-ICE. The length of
the traces between the connector and the AD14060/
AD14060L’s JTAG pins should be as short as possible.
GND
KEY (NO PIN)
BTMS
BTCK
BTRST
BTDI
1
3
5
7
9
9
11
13
GND
2
EMU
4
CLKIN (OPTIONAL)
6
TMS
8
TCK
10
TRST
12
TDI
14
TDO
TOP VIEW
Figure 6. Target Board Connector for ADSP-2106x EZ-ICE
Emulator (Jumpers in Place)
The 14-pin, 2-row pin strip header is keyed at the Pin 3 location;
Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1 × 0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie and Samtec.
The BTMS, BTCK, BTRST and BTDI signals are provided so
that the test access port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins as shown in
Figure 6. If you are not going to use the test access port for
board testing, tie BTRST to GND and tie or pull up BTCK to
VDD. The TRST pin must be asserted after power-up (through
BTRST on the connector) or held low for proper operation of
the AD14060/AD14060L. None of the Bxxx pins (Pins 5, 7, 9,
11) are connected on the EZ-ICE probe.
The JTAG signals are terminated on the EZ-ICE probe as follows:
Signal Termination
TMS
TCK
TRST
TDI
TDO
CLKIN
EMU
Driven through 22 Ω Resistor (16 µA–3.2 µA Driver)
Driven at 10 MHz through 22 Ω Resistor (16 µA–
3.2 µA Driver)
Driven by Open-Drain Driver* (Pulled Up by On-Chip
20 kΩ resistor)
Driven by 16 µA–3.2 µA Driver
One TTL Load, No Termination
One TTL Load, No Termination (Optional Signal)
4.7 kΩ Pull-Up Resistor, One TTL Load (Open-Drain
Output from ADSP-2106x)
*TRST is driven low until the EZ-ICE probe is turned on by the EZ-ICE
software (after the invocation command).
Figure 7 shows JTAG scan path connections for the multi-
processor system.
Connecting CLKIN to Pin 4 of the EZ-ICE header is optional.
The emulator only uses CLKIN when directed to perform
OTHER
JTAG
CONTROLLER
SHARC_A
TDI
TDI
EZ-ICE
JTAG
CONNECTOR
TDO
TCK
TMS
EMU
TRST
TDO
CLKIN
OPTIONAL
SHARC_B
TDI
TDO
SHARC_C
TDI
TDO
SHARC_D
TDI
TDO
JTAG DEVICE
(OPTIONAL)
TDI
TDO
Figure 7. JTAG Scan Path Connections for the AD14060/AD14060L
ADSP-2106x
#n
TDI
TDO
–12–
REV. A
Share Link: 
