ACPL-336J-000E View Datasheet(PDF) - Avago Technologies

Part Name

Description

MFG CO.

ACPL-336J-000E

2.5 Amp Gate Drive Optocoupler with Integrated (VCE) Desaturation Detection, Active Miller Clamping, Fault and UVLO Status Feedback

Avago Technologies 

1 2 3 4 5 6 7 8 9 10 Next

Table 3. Absolute Maximum Ratings

Parameter

Symbol

Min.

Max.

Units Note

Storage Temperature

TS

-55

125

°C

Operating Temperature

Output IC Junction Temperature

TA

-40

105

°C

TJ

125

°C

Average Input Current

Peak Transient Input Current

(< 1 µs pulse width, 300 pps)

IF(AVG)

IF(TRAN)

20

mA

1

1

A

Reverse Input Voltage

VR

5

Peak Output Current

|IO(PEAK)|

2.5

FAULT Output Current

IFAULT

10

FAULT Pin Voltage

VFAULT

-0.5

VCC1

UVLO Output Current

IUVLO

10

UVLO Pin Voltage

VUVLO

-0.5

VCC1

Non Inverting Voltage Control Input Voltage

VIN+

-0.5

VCC1

Integrated LED Driver Output Current

ILEDDRV

20

Integrated LED Driver Output Voltage

VLEDDRV

-0.5

VCC1

Positive Input Supply Voltage

VCC1

-0.5

7.0

Total Output Supply Voltage

VCC2 – VEE2

-0.5

35

V

A

2

mA

V

mA

V

V

mA

V

V

V

Negative Output Supply Voltage

VE – VEE2

-0.5

15

V

3

Positive Output Supply Voltage

VCC2 – VE

-0.5

35 – (VE – VEE) V

Gate Drive Output Voltage

Peak Clamping Sinking Current

Miller Clamping Pin Voltage

DESAT Voltage

Output IC Power Dissipation

VO(PEAK)

ICLAMP

VCLAMP

VDESAT

PO

-0.5

-0.5

VE – 0.5

VCC2

2.5

VCC2

(VCC2 + 0.5)

600

V

A

2

V

V

mW

4

Input LED Power Dissipation

PI

150

mW

5

Notes:

1. Derate linearly above 70 °C free-air temperature at a rate of 0.3 mA/°C.

2. Maximum pulse width = 10 µs

3. This supply is optional and is required only when negative gate drive is implemented.

4. Derate linearly above 95 °C free-air temperature at a rate of 20 mW/°C.

5. Derate linearly above 95 °C free-air temperature at a rate of 5 mW/°C. The maximum LED junction temperature should not exceed 125 °C.

Table 4. Recommended Operating Conditions

Parameter

Symbol

Min.

Max.

Units Note

Operating Temperature

TA

-40

105

°C

Input supply voltage

VCC1

4.5

5.5

V

1

Total Output Supply Voltage

VCC2 – VEE2

15

30

V

2

Negative Output Supply Voltage

(VE – VEE)

0

13.5

V

3

Positive Output Supply Voltage

VCC2 – VE

15

30 – (VE – VEE) V

Input LED Current

IF(ON)

9

16

mA

Input Voltage (OFF)

VF(OFF)

-3.6

0.8

V

Notes:

1. In most applications VCC1 will be powered up first (before VCC2) and powered down last (after VCC2). This is desirable for maintaining control of the

IGBT gate. In applications where VCC2 is powered up first, it is important to ensure that input remains low until VCC1 reaches the proper operating

voltage (minimum 4.5 V) to avoid any momentary instability at the output during VCC1 ramp-up or ramp-down.

2. 15 V is the recommended minimum operating positive supply voltage (VCC2 - VE) to ensure adequate margin in excess of the maximum VUVLO+

threshold of 13.7 V.

3. This supply is optional and is required only when negative gate drive is implemented.

5

Share Link: