ACS8514 View Datasheet(PDF) - Semtech Corporation
Part Name
Description
MFG CO.
ACS8514
Synchronous Equipment Timing Source Partner IC for 2nd T4 DPLL, Accurate Monitoring & Input Extender
Semtech Corporation
'ACS8514' PDF : 86 Pages View PDF
ACS8514 SETS Buddy
ADVANCED COMMS & SENSING FINAL
DATASHEET
Address(hex): 09 (continued)
Bit No.
Description
5
Monitor_DPLL_freq_soft_alarm
The Monitor DPLL has a programmable "soft" alarm
frequency limit. This is an alarm raised that does not
cause a disqualification of the input. This bit reports
the status of the "soft" alarm.
4
T4_DPLL_freq_soft_alarm
The T4 DPLL has a programmable "soft" alarm
frequency limit. This is an alarm raised that does not
cause a disqualification of the input. This bit reports
the status of the "soft" alarm.
Bit Value
0
1
0
1
Value Description
Monitor DPLL tracking its reference within the
limits of the programmed "soft" alarm.
Monitor DPLL tracking its reference beyond the
limits of the programmed "soft" alarm.
T4 DPLL tracking its reference within the limits
of the programmed "soft" alarm.
T4 DPLL tracking its reference beyond the limits
of the programmed "soft" alarm.
Address(hex): 0A
Register Name sts_priority_table
Description
(RO) Bits [7:0] of the validated
priority table.
Default Value 0000 0000
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bit No.
Highest priority validated source
Description
Bit Value
Currently selected source
Value Description
[7:4]
[3:0]
Highest priority validated source
Reports the input channel number of the highest
priority validated source.
Note that if an input is valid and it does not appear
in this field, then the input may have been
disallowed in register 30, 31h.
Register 4B, bit 4 must be set to ‘1’ for correct
setting and reporting of the T4 DPLL priorities.
Currently selected source
Reports the input channel number of the currently
selected source. When in Non-revertive mode, this is
not necessarily the same as the highest priority
validated source.
Note that if an input is valid and it does not appear
in this field, then the input may have been
disallowed in register 30, 31h.
This value will be the same as the highest priority
validated source.
Register 4B, bit 4 must be set to ‘1’ for correct
setting and reporting of the T4 DPLL priorities.
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
No valid source available.
Input I1 is the highest priority valid source.
Input I2 is the highest priority valid source.
Input I3 is the highest priority valid source.
Input I4 is the highest priority valid source.
Input I5 is the highest priority valid source.
Input I6 is the highest priority valid source.
Input I7 is the highest priority valid source.
Input I8 is the highest priority valid source.
Input I9 is the highest priority valid source.
Input I10 is the highest priority valid source.
Input I11 is the highest priority valid source.
Input I12 is the highest priority valid source.
Input I13 is the highest priority valid source.
Input I14 is the highest priority valid source.
Not used.
No source currently selected.
Input I1 is the currently selected source.
Input I2 is the currently selected source.
Input I3 is the currently selected source.
Input I4 is the currently selected source.
Input I5 is the currently selected source.
Input I6 is the currently selected source.
Input I7 is the currently selected source.
Input I8 is the currently selected source.
Input I9 is the currently selected source.
Input I10 is the currently selected source.
Input I11 is the currently selected source.
Input I12 is the currently selected source.
Input I13 is the currently selected source.
Input I14 is the currently selected source.
Not used.
Revision 3.00 April 2007 © Semtech Corp.
Page 37
www.semtech.com
Share Link: 