E6F-AG5C-C7202M View Datasheet(PDF) - OMRON Corporation
Part Name
Description
MFG CO.
'E6F-AG5C-C7202M' PDF : 32 Pages View PDF
Step Number Limit (f5)
With the H8PS, up to 10 steps can be set to turn the output ON/OFF
10 times for each cam. The number of steps that can be set,
however, can be restricted to prevent programming from being added
through operating mistakes. Settings can be made for all cams at
once or each cam individually. The default setting for the Step
Number Limit is 10 steps for all cams.
Example: Limiting the Number of Steps to 2 for All Cams
Collectively.
The maximum number of steps to be set is set using the F5 menu in
the Function Setting Mode.
Display for Collective Settings
CAM
STEP
PRG
Set the cam number to a with the
CAM Keys
and set the
maximum number of steps to 2 with
the Angle Keys
. Press the
WRITE Key to write the setting to
memory.
The cam number can be set to a on the setting display to set all
cams at once. If the number of steps is displayed as “---” when the
cam number is a, the collective settings for all cams are disabled.
Example: Limiting the Number of Steps to 1 for Cam 3.
The maximum number of steps to be set is set using the F5 menu in
the Function Setting Mode.
Display for Individual Settings
CAM
STEP
PRG
Set the cam number to 3 with the
CAM Keys
and set the
maximum number of steps to 1 with
the Angle Keys
. Press the
WRITE Key to write the setting to
memory.
Cam Protection (f6)
Cam programs can be write-protected. Use this setting to protect the
programs for only specific cam numbers. Protected cam numbers will
not be displayed in Programming Mode or Test Mode. Writing or
changing programs will not be possible. Protected cam numbers will
also not be displayed in Run Mode and cannot be checked. The
default settings are for no protection for all cams.
Example: Protecting Cam 3 with an 8-output Model
Cam protection is set using the F6 menu in the Function Setting
Mode.
Setting Display
Not lit (protected)
12
45678
PRG
Set the cam number to be
protected (and not displayed) to 3
with the CAM Keys
and
then press the WRITE Key. The
output display will go out.
CAM
STEP
H8PS
Bank Functions (f7/f8/f9)
The bank function is supported by 16-/32-output models. Banks
enable changing the entire cam program at once by switching bank
numbers (0 to 7).
Cam Program (Bank No. 7)
Cam Program (Bank No. 2)
Cam Program (Bank No. 1)
Cam Program (Bank No. 0)
Control output
Step 0
Step 1
(cam number) ON angle OFF angle ON angle OFF angle
1
45°
90°
135°
225°
2
0°
90°
135°
180°
32
90°
225°
270°
285°
Step 9
ON angle OFF angle
270°
315°
---
---
315°
345°
In Run Mode or Test Mode, the start input must be turned OFF and
ON as shown in the following diagram in order to change banks.
Control the start input when changing banks.
Bank
specification
Start ON
input OFF
Bank 0
T4
T2
Bank 1
T1
T2
Bank 2
T3
Operation
Bank 0
Bank 1
Bank 2
RUN ON
output OFF
Unstable region (outputs OFF)
T1: 225 ms max.
T2: 400 ms max.
T3: 20 ms min.
T4: 20 ms min.
Bank Enable/Disable (f7)
The default setting disables the bank function. To use banks, change
the setting using the F7 menu in the Function Setting Mode.
Setting Display
PRG
Enable or disable the bank function
with the ANGLE Keys
.
CAM
STEP
yes
(Enabled)
no
(Disabled)
Bank Switching Method (f8)
The following methods can be used to switch the bank: the bank
inputs on the terminal block or the BANK Key on the front of the Cam
Positioner.
29
Share Link: 
