RC28F320J3F75 View Datasheet(PDF) - Micron Technology
Part Name
Description
MFG CO.
RC28F320J3F75
Micron Technology
'RC28F320J3F75' PDF : 66 Pages View PDF
Numonyx® Embedded Flash Memory (J3 65 nm) Single Bit per Cell (SBC)
6.0
Electrical Characteristics
6.1
DC Current Specifications
Table 7: DC Current Characteristics
VCCQ
2.7 - 3.6V
VCC
2.7 - 3.6V
Test Conditions
Notes
Symbol
Parameter
Typ Max Unit
ILI
Input and VPEN Load Current
ILO
Output Leakage Current
ICCS VCC Standby Current
ICCD VCC Power-Down Current
ICCR
8-Word Page
ICCW VCC Program or Set Lock-Bit Current
ICCE
ICCBC
VCC Block Erase or VCC Blank Check or
Clear Block Lock-Bits Current
ICCWS
ICCES
VCC Program Suspend or Block Erase
Suspend Current
—
±1
— ±10
50 120
0.71 2
50 120
15 20
30 54
35 60
40 70
35 70
40 80
—
10
ÎĽA
VCC = VCC Max; VCCQ = VCCQ Max
VIN = VCCQ or VSS
ÎĽA
VCC= VCC Max; VCCQ = VCCQ Max
VIN = VCCQ or VSS
CMOS Inputs, VCC = VCC Max; Vccq =
VccqMax
ÎĽA
Device is disabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30),
RP# = VCCQ ± 0.2 V
TTL Inputs, VCC = VCC Max,
Vccq = VccqMax
mA Device is disabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30), RP# = VIH
μA RP# = VSS ± 0.2 V, IOUT (STS) = 0 mA
CMOS Inputs, VCC = VCC Max, VCCQ = VCCQ
Max using standard 8 word page mode
reads.
mA Device is enabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30)
f = 5 MHz, IOUT = 0 mA
CMOS Inputs,VCC = VCC Max, VCCQ = VCCQ
Max using standard 8 word page mode
reads.
mA Device is enabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30)
f = 33 MHz, IOUT = 0 mA
mA CMOS Inputs, VPEN = VCC
mA TTL Inputs, VPEN = VCC
mA CMOS Inputs, VPEN = VCC
mA TTL Inputs, VPEN = VCC
Device is enabled (see Table 17, “Chip
mA Enable Truth Table for 32-, 64-,
128-Mb” on page 30)
1
1
1,2,3
—
1,3
1,4
1,4
1,5
Notes:
1.
All currents are in RMS unless otherwise noted. These currents are valid for all product versions (packages and speeds).
Contact Numonyx or your local sales office for information about typical specifications.
2.
Includes STS.
3.
CMOS inputs are either VCC ± 0.2 V or VSS ± 0.2 V. TTL inputs are either VIL or VIH.
4.
Sampled, not 100% tested.
5.
ICCWS and ICCES are specified with the device selected. If the device is read or written while in erase suspend mode, the
device’s current draw is ICCR and ICCWS.
Jan 2011
208032-03
Datasheet
21
Share Link: 